The variations of LUTZ BLADES serrated knives are enormous in the cutting edge shape. Shaft height and angle can be adjusted to the material to be cut. Here we have been producing a very wide range for decades, e.g. corrugated blades for the production of potato chips in crinkle cut..
Shafts can be made inward, for an aggressive needle-tip cut, or outward, for a soft permanent cut. Our knives always catch the perfect wave!
Product recommendation
2517-1200×750
How you benefit
High quality cutting creates best cutting results
Complete production on CNC machines for best product consistency
Contour shape of the shafts after consultation
How to draw
Equal sharpness from blade to blade
Wide range of materials and hard coatings
Surface coatings of the blade body for lowest friction
5897
Completed Orders
15
Qualified Engineers
5+
Work Facilities
3+
Worldwide Branches
OUR COMPANY
The wide range of materials for our blades
Our product portfolio offers you blades in thicknesses between 0.06 – 3.0 mm and with final hardnesses between 40 – 85 HRc. You also have a wide choice in our material program:
Standard hard material with high wear resistance and relatively high coefficient of friction (against reference material steel approx. 0.4 to 0.7), usually gold-colored, safe application range up to approx. 300 °C.
TiAlN
Has greater oxidation resistance than TiN with comparable coefficient of friction, usually anthracite blue.
Blueing / Blackening
Applied over the entire surface, light corrosion and starch protection, also serves as a distinguishing aid.
Teflon® (PTFE)
Teflon® non-stick coating (PTFE); due to the very low surface tension, practically no foreign bodies stick to the cutting edge, resistant to acids and alkalis; significantly reduced frictional resistance; the very low static friction allows jerk-free cutting (therefore very suitable for the medical sector); low wear resistance; not suitable for contact with sodium and at temperatures above 250 °C.
TiC
Has lower wear resistance than TiN with significantly lower coefficient of friction (against reference material steel approx. 0.3 to 0.5), usually anthracite colored.
ZrN
With a wear resistance similar to TiN, but denser structure (morphology) than TiN and thus greater resistance to pitting under appropriate load, usually steel colored.
CrN
Has lower wear resistance than TiN. Advantage of CrN: lower residual stresses than TiN. Therefore partially useful for applications with high bending load.
TiCN
Intermediate coating material between the high wear resistance of TiN and the low coefficient of friction of TiC, relative position between TiN and TiC depending on the ratio of C and N, usually anthracite color.
DLC
Has high wear resistance with low coefficient of friction (approx. 0.1 against reference material steel); susceptible to impact loads and high temperatures (between 100 and 300 °C depending on structure).
Color varnish
Applied over the entire surface, serves as a sorting aid for different material thicknesses and as corrosion protection.
Customized quality
Do you need a blade that is tailored to your individual cutting process? Which, even if produced in small quantities, has a near-series quality? Our development department has the right answer to these questions: prototype production by LUTZ BLADES.
How you benefit
Near-series initial samples.
Maximum flexibility = customized blades.
Smallest quantities possible.
Efficient and accelerated product development.
Development and optimization of the blade before series production.
The Lutz BLADES Rapid Prototyping
Cutting of the blade geometry by state-of-the-art machinery and CNC-based grinding of all radii.
Automatic measurement and testing of the tightest tolerances in the process.
Customized heat treatment and coating.
Do you have individual wishes?
Do you have a question? A concern? Or a suggestion? Do not hesitate to contact us. We have the right experts for all matters, who can help you with certainty.
Company Details
M.H.B General Trading LLC
Ginger Business Center
Alkhabisi, Deira
Dubai
